Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi,
I wanna use nrf51822 as master which has 2 slaves: sdcard (fatfs) and adc
I set SPI_INSTANCE 0
and they don't want to work together, I mean I'd like to write some...
A time T_PINR is specified in the datasheet, as shown in the snippet below.
Does this give me an indication of the pulse width for a pin reset? If so, how do I interpret...
Not really a question, just that I find the comment misleading. In the sdk_config.h example coming with the SDK there is this piece of code:
// <q> SAADC_CONFIG_LP_MODE...
Hello,
I am trying to establish communication between Win 10 PC and nRF52 Dev Kit using pc-ble-driver . I followed the instructions in:
https://github.com/NordicSemiconductor...
RN2903 is LoraWAN module using ASCII Command Interface over UART.
RN2903 is connected with nRF52-DK.
I'm connected uart line tx, rx gnd.(cross connect...)
UART communication...
Hi,
My desire is to connect a BC832 module (with nRF52832 on it) to a UART on a controller board and then send data from an iOS app (programmed in Swift) through the BLE...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
I need to drive a stepper motor without software intervention, since strict timing is a must.In the following image you can see the required wave-forms - the motor requires...
The SD API (S132-6.0.0) documentation provides little beyond what one could guess from the function and type names. sd_mutex_acquire says "Attempt to acquire a mutex". nrf_mutex_t...
Hi i am doing a prosject to get notification on cell phone when i get mail in my postbox (postbox outside the house) I am using a nRF51 dongle, and want it to connect to cellphone...
Hi! I'm working on HID mouse example on SDK 13.0.0. I'm supposed to use this as a low power media button control. I've done a few modicifations on the code for power optimizations...
