I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
I am advertising a service and providing scan response data. It is not clear to me whether I should be bothering setting up the values of the ble_adv_modes_config_t structure...
Hi there,
i am very curious about what can be considered as interrupt factor in receiving the signal from beacons, so if these scenarios have been tested please provide...
I'm using the nrf52832-QFAB variant (32K RAM 256K Flash)
The part is marked as NRF52832 QFABB0 1630AC
Surprisingly, this part is happily running my application and bootloader...
Hello,
I can't find where in flash the peer manager data is stored. I'm currently working on DFU support and as part of that I want to define the memory area that should...
As per mesh_hw_resources.md (MESH_SDK/doc/introduction)
## Flash lifetime The flash hardware can withstand a limited number of write/erase cycles. As the mesh stack uses...
Hi all,
I am trying to develop the BLE Heart Rate Collector example on the nrF51 Development Kit. As far as I read in the Nordic web ( http://infocenter.nordicsemi.com/index...
I'm trying develop on a custom board based on the nRF52832 and am running into some issues. When I run the blinky application (with no SD) the application executes fine. However...
Hi I'm developing beacon firmware using ble_app_beacon example code.
I was able to send good beacon data for my purpose. For the next step, I want to turn on the LED which...
Hi,
I am using a custom board based on nRF52 (nRF52832-QFAB-R) and programing it with softdevice.hex and "ble_hid_mouse" example application in the nRF5 SDK v14.2.0. the...
Hi,
I am using softdevice S132 V2.0 for nrf52832 controller.I am using BLE UART app. It is working fine on eval board.But when i checked it on custom board developed by...
Hello,
I am using sdk12.2.2 and nrf52. I have implemented fds_read, fds_write, fds_delete and its working as expected. Now when I am trying to use fds_update my data is...
We are trying \Nordic\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I want to control UART. If device is not in use i want to...
I'm just starting to bring up a custom board based on the nRF52832 and I am unable to program it using the J-link. It looks like my reset line gets stuck low when the JTAG...
