Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
I Modify my code for 7 buttons from 7 gpios. But my code has a issue at sdk_config.h. The define of GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS is 9. When I built the code and download...
Hi all,
The nRF52832 spec. document specifies that the current consumed in System OFF / No RAM retention / Wake on LPCOMP mode is 1.9uA. However, if I measure the current...
Hi,
A couple of months ago, the Bluetooth SIG published a specification for LE Audio : a new codec and method to send audio data through BLE 5 connection.
Is there an...
Hello,
Few questions about NUS and NUS C please.
Is there any way to know how many TX are pending ?
Are TX notify or indicate ? How to change it please ?
Thank yo...
Hello,
Based on aws_fota sample, I want to replace the line with poll with something that not blocks (because I have another things to manage in my loop). Do someone have...
