Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Dear Nordic: My use scenario may be a little complex. I try to describe it clearly. A device developed on NRF52832/S332/SDK13, acts as a combination of Bluetooth central,...
Hello,
I have received Thingy 91 for demo purpouses including the SIM from iBasis, but I am unable to set up the device as it is not connecting to the cloud.
I have linked...
Hi,
I use a board from Adafruit with NRF52832 to make a POC (Proff Of Concept) (Adafruit Feather nRF52 Bluefruit LE - nRF52832 - PRODUCT ID: 3406).
I use the Arduino IDE...
Hi,
Problem description
I wrote a program that initializes the modem (LTE-M) and goes on to send one UDP packet every second (is just the counter).
The server receives...
Hi,
I'm trying to implement some direct advertising, but I'm a little lost in the process.
Could you provide me with an example of code ? I read somewhere that ble_app_hid_mouse...
Hi,
I want to make RPI bluetooth //meshctl app works along with nRF Mesh App. Objective is to make Raspberry pi has non provisioned node, use nRF Mesh to add RPI has provisioned...
When I use the nRF Sniffer on a 52840 or 52832 with Wireshark I can see the RSSI values for each advertising message for all 3 channels (37, 38, 39). So for each advertising...
Hello I would like to use both UARTES in the exemple "ble_thread_dyn_mtd_coap_cli_pca10056_s140". I tried to adapt this example using the example "nRF5_SDK_for_Thread_and_Zigbee_v4...
I am using SDK 15.3, SES 4.3 and SD 130. I've added the saadc example code into my code which is comprised of the ble_central, nordic UART and saadc.
I've changed the timer...
Hi!
I just got the Thingy:91 to play around with, but the modem firmware is old. Is it possible to update the modem firmware using USB and the Programmer software? The ...
Hello,
I am trying to build a Zephyr application for the Thingy91 which uses the I2S module to receive audio data from an external microphone and sends this data via BLE...
Hello,
i would like to point out what i think is a missing dependency in file "include/modem/modem_info.h". At row 187 there is:
but at_param_type is not declared in...
I am going through the steps for building a secure bootloader
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
However I...
Hi,
I am trying to better understand the eSIM provisioning process. I want to verify that the IMSI changes to a local profile after the first registration with the provisioning...
Hi Nordic Devzone readers,
Recently I've picked up a NRF9160DK and have tried to program my own user program onto it. This will consistently fail unless I hold the reset...
