Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi, I'm getting a crash when discarding an advertising packet.
Roughly what I do is:
Which crashes at advertiser_packet_discard().
GDB trace:
It looks like packet_buffer_pop...
When and by what logic Peer Manager performs garbage collection on FDS?
I have a single number stored also in FDS and I’m wondering if gc performed by Peer Manager will...
Hello,
I'm still just starting to deal with Zigbee and I have a question. I use 2 nRF52840 chips. One as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
Hello,
I never used BT modules before. I'm going to buy some bluetooth modules to add wireless to an existing board.
I need module with following characteristics:...
Hi，I want to write the firmware to 52832 from android system by UART .I have readed the firmware into bytes, and then do not know how to compose the bytes to write into serial...
I have the following situation:
My device receives a number of RF packets, changes to TX mode, sends some data, goes back to RX mode and it should be able to access the...
Hi,
my application is normally a BLE scanner, listening for beacons. This runs OK.
Now, I tried to add a tested piece of connectable gap/gatt firmware, that runs fine...
Hi ,
in the RTOS example, you set
configTICK_SOURCE as FREERTOS_USE_RTC and configCPU_CLOCK_HZ as( SystemCoreClock ) .Since SystemCoreClock is 64mhz, why did you not set...
I am trying to understand why when I connect the nRF52840 Dongle using nRF Desktop I get this message in the log:
2020-02-26T23:12:13.293Z INFO Connectivity firmware version...
Hi Team,
We are using nRF 52840 chip for our development of product.
As of now the settings for BLE data transfer are as below.
MIN_CONN_INTERVAL 20 // which is the...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
