Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Hello,
I have not seen any mention of a BlueZ based BLE DFU library other than here , which was a long time ago.
I will require this library for my current project so...
Hi team,
My customer needs to make some adjustment on I2C frequency due to their SW requirement. As our reference on datasheet, I2C frequency needs to be 100kbps, 250kbps...
Hey, i want change the simple_on_off model a little bit, so the server return an byte array to the client get_message, can you say me how to include vendor specific model...
If nrf_gzll_ok_to_add_packet_to_tx_fifo() returns false and nrf_gzll_get_error_code() returns nothing, what does this mean?
Facing this a lot when trying to change channels...
Hello,
I was trying to perform DFU over mesh. My setup was as followings:
7 nrf52832 Devies. One of them is connected to my laptop.
I programmed those according to this...
Hello,
I'm using the nRF51422 with a dfu dual bank bootloader with SDK 11. I can programm the uController with the Softdevice and the bootloader and afterwards load successfully...
Hello, I'm trying to add a Peer Manager functionality to the Mesh Provisioner application.
I'm using nRF52832 devkit, Segger Embedded Studio, nRF5 SDK for Mesh 2.0.0 and...
Hi,
for some reason I cant debug in Keil, the program doesnt stop in main.
I also have NRF_LOG enabled, but nothing appears on RTT.
What could I do?
Thanks!
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132.
My hardware is a custom board with a Rigaldo BMD300 module (contains...
Hello,
I'm trying to modify the dfu_dual_bank_ble_s130_pca10028 bootloader so my device would start with the application and after a signal (with the button) it should...
I have an application where a unit contains a nrf52840 and will act as a central device, collect the data from peripheral device and store into the onboard memory. Upon the...
Hello,
I'm seeing higher than expected power consumption when running an RTC peripheral using LFXO as the LFCLK source compared to using the internal RC. Specifically, I...
Hi, to repeat the problem, you need to press button 3 and then button 2 on the board with an example of dimming_client, after that the board with dimming_server stops responding...
Question 1 :
I write 512 words to flash but only can get some value right .and some value was wrong.
I used fs_store( &one_min_data,
(uint32_t *)(FLASH_DATA_ADRR), ...
