Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I would like to confirm that my hardware design is correct and in addition that I am following the correct procedure to place the nRF52832 to sleep to achieve the lowest possible...
It works with SDK v12.3 and soft device 3.0.0. Does not after porting to 15.2. This is a custom board (extremely common configuration with single 32Mhz crystal) that serves...
Hello,
(I also create an issue over Thingy SDK GitHub page - #29)
It seems to me that there is an issue about the usage of MPU-9250.
I motioned Thingy and I observed...
Hi,
I am trying to get DFU working on my PCA10040 board using SDK 14.2 and armgcc toolchain.
I have followed the instructions to set up DFU here:
devzone.nordicsemi...
Hi,
Whenever I call `nrf_malloc` with a parameter bigger than 32, the pointer remains NULL. I think it's related to some sdk setting but I couldn't find it.
Anyone had...
Currently, I am working with the Nordic SimpleOnOff Model of the Light switch in the Bluetooth Mesh.
I am good that the light in the mesh can be set on/off after Provisioned...
HI guys,
I am running a beacon based on the ble_app_beacon example. This works fine.
Next, I made a connectable GAP/GATT application to read and make some settings. This...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/lib_timer.html?cp=4_0_0_3_51_0_0#lib_timer_debugging
The link to " Monitor Mode Debugging -...
I flashed the Mesh serial hex file on nRF52840 dongle. I can see my dongle on nRF connect mobile application but not on nRF Mesh mobile application. So do I need the development...
I flashed the mesh serial hex file in two dongles and used one dongle for connecting it to the nRF Connect Windows application. The hex files were present in the nRF SDK for...
Dear Sir,
Whitelist(on periperal side) are used for filtering scan requests( onlly allow the scan requests from the devices whose address is there in the whitelist with...
I'm using ble_app_uart example.
The board go in low power mode, but after 3 minutes (#define APP_ADV_DURATION 18000 ) go OFF. I need that remain in advertsing mode always...
I was developing an green house system for plants which was based on nRF51822 SoC. The system was fully completed and working fine except one problem which was reset of nRF51822...
I am trying to find the optimal way to automate some tests that I run on my BLE device. In this test, I need to write a specific hex value to a custom BLE characteristic of...
