When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I have a smartwatch, smartphone, and tablet.
I went to some place without any other bluetooth devices, my devices are able to scan and pair with each other. But nRF-51 not...
Hi,
I have followed sequence in http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fsdk_app_serial_dfu_bootloader.html&cp=4_0_0_4_3_4...
Hi,
I have a beacon code for nrf51 that I wanted to port to nrf52. It uses app_timer, gpiote and adc. The power consumption in idle is ~30uA. Now I wanted to port this code...
FDS_VIRTUAL_PAGE_SIZE
The size of a virtual flash page.
Expressed in number of 4-byte words. By default, a virtual page is the same size as a physical page....
Hello,
I would like to use proxy_server(example of light_switch ) and ble_app_blinky_c, to make these two functions work together in one card. So this card can be controlled...
Hello everybody,
i have crated an Report id for the telephony usage on iOS from here https://opensource.apple.com/source/IOHIDFamily/IOHIDFamily-247/IOHIDFamily/IOHIDUsageTables...
Hello All,
I'm trying to program a NRF51822 module for the first time.Using Keil, Soft device s110_nrf51_8.0.0,soft device kit nRF51_SDK_9.0.0_2e23562 when I try to program...
I found the next response in a topic and i would like to know if there are some new improvements in the last SDK mesh 2.01.
devzone.nordicsemi.com/.../120547
I turn off...
I have installed from "nrfgostudio_win-64_1.21.2_installer" on Win-10 laptop. Weh I start nRFgoStudio, the main window appears for a second then I get a message "nrfgostudio...
Hi all, we're using code from this forum to enable GPIOTE and PPI to measure the low between the arrows to indicate a "start of transmission" and then switch to measuring...
Materiel and software use :
SDK mesh 2.0.0
SDK 15.0.0
NRF52832 with PCA10040 x5
Situation :
I would like to implement this network :
I follow the instruction...
I'm using the UARTE peripheral via the UART driver code in SDK v14.2. Due to transfer size and SoftDevice timing I have to use the double-buffered receive method (by calling...
Hello,
I am trying to make a beacon start advertising on a long press of a button. Using this as a reference, I implemented a timer as follows:
this is the flag to keep...
Hi!
I am using SDK15, my application is based on app_ble_uart. I have added my proprietary characteristic to NUS next to RX and TX Characteristic with quite a success. Now...
I use sdk14.2 nrf52832 as the primary, connect two iphone peripherals, iphone is connected to broadcast, when I turn on both peripherals, sometimes everything is normal, sometimes...
