Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hi,
I'm using ncs 2.9.0.
I configured the GPIO in device tree like this:
And I used it in .c as follow:
But FATAL ERROR was got when the gpio_pin_interrupt_configure_dt...
When doing the scan of all possible Bluetooth devices on nRF Connect for Mobile, our custom manufactured Bluetooth wearables are not consistently being found. When by chance...
Hallo.
I am working with Thingy.91x and after learning almost all lessons with Nordic Dev Academy, LTE fundamentals, i have encountered an issue.
Right now I can't use...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
Hi,
how to convert/format NCELL data to data that you can use to find the cell on a cellmapper.
This is a ncell result: %NCELLMEAS: 0, “06223A0C”, “20610”, “5334”,65535...
Hi,
I am currently working on making it possible to connect with different devices sequentially. It was told to me that it is possible to first scan all devices, and then...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
While testing CoAP with NB-IoT I normally get PSM (sleep) delay = 20s before PSM mode is set (0.5mA with UART enabled), but after awhile PSM delay increases to ~4.5min (at...
Hi,
I recently added FOTA support on my project which runs on nRF5340 + nRF7002. I am currently working on a devboard, nRF7002DK.
Previously, I was running the project...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
Currently the nrf-connect extension offers board targets under build configuration. These are categorized as "Nordic SoC", "Custom boards", "All". As I have understood...
