Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
Hi,
My nRF5340-DK (serial number 001050065828) suddenly stopped being detected by USB on Windows 11 after months of normal operation. I did not change anything in the hardware...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hello Nordic engineers,
I maintain the lolren/nrf54-arduino-core project: a bare-metal Arduino core for nRF54 boards that deliberately avoids Zephyr and vendor RTOS dependencies...
Dear nordic This ticket is a feature request to implement SSL max_fragment_length of 2k while initiating a TLS connection, when offloading TLS to the NRF9160 modem. As stated...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
When performing a DFU using the latest iOS nRF Toolbox I keep getting an "Error on init Packet Message:Operation Failed". The DFU works fine with the same firmware application...
