I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi, I'm just starting to learn my ways around the nRF5182 SDK, my goal is to implement a device with HID profile using this device. The device must work with Windows 7 (until...
I would like to profile some code execution time (moving between floating point and fixed point arithmetic). On the last Cortex-M3 I used, we had the DWT_CYCCNT register at...
Hi ,I am evaluating the nRF58122 for BLE devices.
The nRF51822 Can we use "Multi-drop debug" on SWD?
We will use together also ARM microcontrollers other, I want to know...
this is quote from AN36> 4.2 Set up
The nRF51822 Evaluation Kit is needed for this application example. However, it is possible to modify the
project to also work with...
Hi!
I know this might be a stupid question to you but still... I am not able to disable i.e. a timer0 cc(3) IRQ.
My way to enable it in first place:
NRF_TIMER0->INTENSET...
hi guys,
i am trying to write my own application using ble_app_template for nRF51822, but i am not at all understanding the code, did anyone developed the code for it?...
hi,
i add bond function on my project ,
now the Master Control Panel can work correctly(show the Confirm Box )
but the iOS app(on LightBlue),not show any Confirm Box for...
Is possible to put S110 in observer role (as peripheral) , waiting for a specific advertising (or waiting for an active scanning) and then switch to advertiser role (always...
Hello all,
I'd like to use NRF UART App sample code (newest iOS7 version) to send data from iOS6 to nrf51822 for "real time" data transmission. But I found that when I...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
Hi experts,
i found one issue that if i continue to make the 51822 advertise(if advertise timeout, start again), sometimes the 51822 will stop in somewhere. I'm sure that...
I have just acquired the NRF51822 Evaluation Kit and going through the getting started documentation. I can't seem to fix a compiler error which is highlighted in Kiel uVision...
Hi,
I am starting my first project with nRF51822 for my thesis.
I thought its a good idea to start with evolution kit so I bought nRF51822-EK
I assume I will get everything...
