We have two organizations/projects in our nRF Cloud account:
Jackwoida 51789c46 Team (retain)
James_Eval (remove)
I am the account owner/administrator. The James_Eval...
i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi all:
Q:When i reboot the board which burn the serial project , how to add the device key to serial board again?
I use PYACI to control the board which burn the serial...
Hi,
I have couple of question regarding ble_app_hrs_freertos example (sdk 14.2)
Possible bug - in main() , erase_bonds is a local variable (defined on the stack)....
Hi!
1. Is there any method to make paring and bonding without radio channel? For ex. write any data directly to .hex to periph and central devices.
2. Is it possible to...
Hi Everyone
I have added all the required paths for the ble_app_uart example but the program can not find the files like ble_advertising.h and nrf_sdh.h files which are...
hi support
Thinking of attendance system using bluetooth Identity cards
what is maximum nos of cards can a nrf52 scan at a time.
suppose there are 100people in a room...
I have just received my development kit and following the getting started instructions on website. But I am stuck at point 7 of this link https://www.nordicsemi.com/eng/Products...
hello Nordic team
I am using nrf52DK.how to use spi to read /write data .I have seen sdk14.2.0 in folder nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi.
I am trying to interface an atmega32 with an nRF24L01. I am trying to communicate between two nRF's. But before proceeding to that, I set out to test the SPI connection between...
I put the nrf_ble_ancs_c_request_attrs in the BLE_ANCS_C_EVT_NOTIF event(added). But only return back 1 or 2 BLE_ANCS_C_EVT_NOTIF_ATTRIBUTE event. I am using 12.3.0 SDK example...
Hello,
This in reference to Case ID: 121570.
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery from Panasonic. We have calculated...
i am using my custom board with nrf51822 and using sdk 12.3.0 .
the led blink example works fine on it but when i upload ble_app_uart then bluetooth is not advertising.
Hi i just get nRF52832 PCA10400 DK.
I am using SDK14.0.0. i tried to use /example/peripheral/spi.
i don't set the gpio set and high or low.in the SDK14.0.0, how to set...
Hi!
I'm using a barebones example project from SDK 12.3.0, under examples/peripheral/uart, with two versions of nRF52-DK boards (pca10056 and pca10040). The goal is to read...
Hi,
I am looking for the carrier tape spec for nRF52810-CAAA.
I am referring to the following document but nRF52810 is not listed.
nWP024 - Embossed Tape and Reel...
