after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
Hi,
I have a BLE application, which I want to interface with PC via serial communication through USB.
It seems that just adding Softdevice breaks the USB_CDC_ACM example...
Hi all,
As a followup of this question, I started with the Thingy Mesh Provisioning Demo v0.5. However, I cannot get this version working possibly due to some unclear points...
Hi,
Am developing a beacon using nrf52810. I have a doubt on how to program the nrf52810 which I made using the schematics and layouts given in the Nordic website for nrf52810...
I am noticing that FDS requires me to specify a "record size", but there is no maximum specified, so I am testing it. Currently my program attempts to store 32 words, but...
I want to add some code to static void app_onoff_server_set_cb(const app_onoff_server_t * p_server, bool onoff) in light switch server application.
My intention is when...
