Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
i.e. it would be similar in type to the nRF24L01 radio code, but obviously different since it's part of the vastly different nRF52.
Any examples to draw upon?
Unable to get logging information for SAADC example project in SDK versions 15.0.0, and 15.1.0.
I have no problems accessing the logs for the ble_uart_app example project...
I want to do power profiling in my nrf nrf51822 devices. Nordic don't have any online tool to calculate current consumption for the nRF51 series. So how to calculate current...
Hello, We are using nRF51822, SDK12.3.0 and softdevice S130. It is a multiprotocol application using the softdevices' timeslot feature: Our protocol running in timeslots concurrent...
Greetings,
We are currently certifying a device to be compliant with FCC & IC rules in the US & Canada. The upper band edge measurement is failing on advertising channel...
Dear Support,
We are in pre-certification phase with our product using nRF52840.
For RF testing purposes, our testing house asked us to provide the following, and I am...
Dear Nordic,
I configure a GPIO pin to PWM output, from this diagram, if we enable `PIN[0].CNF.INPUT`, we can read GPIO status while the PWM is running. But I check the...
Hi
Am I alone in my judgement that some of the Nordic Example code is a good example of how NOT to code? These examples should demonstrate the perfect way to utilise a given...
I want to develop a custom Firmware for the Thingy:52.
I am using a Segger Edu J-link Debugger and the Thingy:52 PCA20020 Version 1.0.0. As an IDE i am using 64bit Segger...
Hi,
I'm using nRF52832 with SDK 15.0.0 base on ble_app_uart example. But I meet a very strange problem. The project couldn't run after I program, no matter I use IAR or...
Hello, under Android I can access the GATT stacks via SDK ( API ). Is this under Windows 10 also possible to access the GATT stack via SDK ( API ) ? Or must I develop a special...
Dear Nordic
how i test one channel advertising?
I change inside advertising_init()
ble_gap_adv_params_t m_adv_params;
m_adv_params.channel_mask[4] =0x60; // advertising...
Hello,
For my projects I use python script to download sdk from https://developer.nordicsemi.com . For some reason newest sdk 15.1 is not available there, only here https...
Hi,
1. I need to know the bluetooth 5 range of the nrf52840 dongles which I need to use on custom boards.
2. Can I use AT commands to communicate with the dongle over...
Hi,
We are trying to get the serial dfu example from sdk 14.2 working with an nrf52832. After flashing the device succesfully and starting up the bootloader we were unable...
