Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi there,
one quick one:
when configured as SYSTEM RESET, Does P0.18 acts as an Input/Output? i.e. will be asserted Low by the NRF52840 while the MCU is in reset?
...
Hi all,
I'm using ble_app_multirole_lesc example to develop my application, it connect to android phone as peripheral role and now I need it to connect to another nrf52832...
If I have the J-Link RTT Viewer open and connected to my PCA10056 (viewing RTT output from an external board connected to P19) and then reprogram the board using nrfjprog...
Hello,
I am currently running into an issue with nrf51822. I am trying to write in flash a flag which defines the device I use. Indeeed, the device on which the code will...
Hello,
I want to us the nRF52 dongle with BLE and ANT communication. I downloaded SDK 15.2 and looked at the examples. I can see a lot of examples for ANT and for BLE individually...
Hi Sir
I try to write/read/earse any address with length 32.
but some bytes shows zero "0x0" when I use , it should be 0xff after erasing...
Do you know what's the problem...
SDK: 15.0, PCA10040
Hi, I am trying to add multiperipheral to Multiperipheral LBS example and I get this error .\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
Hi, I'm trying to add multiperipheral option to usbd-ble-uart example and for that I checked the example ble-app-multiperipheral and I can't find the way to do that so my...
Hi.
I have a project with usb_cdc merged with multilink_central and NUS service. It is working quite well, multiple peripherals can connect and send data to the central...
Hi,
Currently I am sounding a simple beep on and off sound with a Piezo Buzzer on the nRF52832 and using the power profiler, it is consuming approx 713.323 μA, I was wondering...
Hello!
I have a question about the slave latency: I know how it should work, I would like to know if it is normal that there are current peaks in the supply current when...
Hi,
Does anyone have a hex code that can be added to the app hex in order to get rbp for NRF52832? Or a code that can be used from Arduino IDE?
I know that it can be...
Following error throwing while using nrf tools
nrfjprog verion 9.3.1 -------------------------------------------------------------------------------- FUNCTION: open_dll...
