I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I have PTR9818 module and NRF52840 Development Kit. I flash firmware CLI example(SDK for Thread and Zigbee 2.0.0) for PTR9818 module and communicate with PC use USB-USART...
Hallo,
Currently I'm investigating different Low Energy Bluetooth solutions for our healtcare products that we build in Televic Healthcare.
So here is the setup I...
Hi all,
I'm a little bit confused with the Thingy52 SDK.
The "ble_app_thingy_s132_pca20020" code is the same of the "thingy_v2.1.0.HW_1.0" precompiled hex file?
Thanks...
Hello
I would like to know GPIO leakage current, especially when the GPIO outputs Low
state, leakage current flow thorough the High side MOSFET parastic diode.
If nobody...
Hey everyone,
I have measured input current by different transmit powers:
nRF52840
Equipment: Konstanter ssp 240-40 as current source
Agilent 34401Afor current measurement...
I have a custom board on which I am running the fatfs example from SDK15.2.
On SD Card Initialisation the CMD0 response is unexpected: -
Where the NCR would be expected...
Hello-
We are preparing a product for Bluetooth certification. Our design has a PCB antenna and the the testing house is requiring an SMA RF coaxial cable to interface...
I have created a custom Board Support file for my custom Board But it is not able to advertise the BLE Device after I use My custom Board File. When I use Predefined board...
Hi,
We need to collect sensor data from nrf52832 and after some processing, we plot data and generate some notifications etc. on smartphone app.
Shortly we need to design...
Hello, I'm developing a solution by using MESH SDK : nrf5_SDK_for_Mesh_v2.1.1
There is an ASSERT on access.c in nrf5_SDK_for_Mesh_v2.1.1_src\mesh\access\src\ as below. ...
SoftDevice: S132_5.1.0
Environment: I have 1 Device Advertising and about 200 "tags" waking up every 10 seconds and scanning for those advertisements and connecting, I have...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
