I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello,
We are working with Low Energy sensors that are programmed to make a periodic ADVs to our scanners/apps/Raspberries, in order to start a service if required. So the...
Hi,
I am using cli and made my own command like bellow, as you see i have a command with 3 sub commands. But i think my idea is primitive because if i have 1000 sub command...
I am starting building industrial-grade system which contains several nodes connected via wireless channel.
As a wireless protocol I decided to use BLE 5 due to long ranges...
I am trying to program mpu_simple https://github.com/Martinsbl/nrf5-mpu-examples with Segger, and I get to connect sensor MPU6050 to my board but I do not receive datas of...
Hello. I followed all the steps provided in the readme document. After dragging and dropping the hex file to the j link, the led 1 starts to blink, indicating that the board...
With an nRF52, is it possible to wait longer to measure the RSSI on a channel? I'd like to measure the RSSI over 1msec or so, rather than a tiny 8us (typical) snapshot.
Hi,
This is my first time to use Nordic product and I have used nRF52832 based SDK 12.0 and SoftDevice132 v2.0 about 2 months. And the IDE used for devlopment is KEIL MDK...
Hi
Im using the DFU secure example (examples\dfu\bootloader_secure\pca10028)
Im working on a NRF51822-QFAA ,S130 SDK12.3 , Im not sure about my IROM/IRAM definitions,...
Hi Nordic Team, One of our customer wants to integrate communication via Thread BLE on his IoT-Gateway. We found your nRF52840 Dongle. Does this dongle have any certifications...
Hi,
I am planning on using nrf52832 for a beacon application. I happen to get a schematic and layout from Nordic website for development.
I am attaching the schematic...
Hi, I am trying to interface MPU^)%) sensor with NRF52832. with help of BLE UART. i will get the resultant data on BLE APP. but here i got some error is this the linking error...
Hi,
we want to made the device which should working in the mesh network without provisiong procedure by user.
Typical application - network with 500 nodes, every node...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
