Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi team,
I was comparing the ble_app_hrs example from SDK v15.3.0 to SDK v16.0.0 and noticed a big difference in the average power consumption. The only change I made to...
I am testing the ble_app_blinky example on nRF52840 BLE SoC and the "nRF Blinky" Android application example which uses the Android-BLE library from NordicSemiconductor. My...
The current implementation of Mesh Config using the flash manager lack a memory listener which can cause it to never retry a store or delete operation.
Assume the following...
Dear Sir,
Could you please recomend board(hardware) that I could move my code that was developed using NRf52 SDK.
I am using ANT functionaluty and s212 software
Best...
Hi Nordic,
I had an initial project with a multilink central connecting to several peripherals through a NUS service, the system is working OK but then I added another connection...
I am using PCA10040 development board for flashing.Same it was working fine to flashing the Custom board.
Now suddenly not flashing to the custom board same board which...
I am planning to use CP2102 (USB to UART) and RF-BM-ND06 NRF52840 bluetooth module for sniffing BLE packets .
Or as an alternative for Nordic Bluetooth USB dongle.
But...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
0> <debug> nrf_sdh_ble: BLE event: 0x26. 0> <error> app: Fatal error
I started with the nrf_tempelate project and used nrf_uart to add uart service. It works fine but after...
Hi,
I want to know that, can we use this nrf91 for transferring the real time data with tab or mobile phone beyond BLE range. I mean, do we analyse the real time data from...
Hi:
I have no dongle or any other Dev board such as PCA10031. Can I use nrf51822 and cp2102 as a usb dongle to work with MCU of PC? If the answer is yes, what should I do...
Hi All,
I am trying to decrypt some data coming in on my board with AES ECB mode. I know that there is no decryption function for ECB and you have to use the same sd_ecb_encrypt...
Hello, We are completing a project where is used the BLE device nrf52832. The product is composed by 2 devices: a peripheral and a central (both with nrf52832). The broadcaster...
