Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
we are working on a test program with a thinghy:91 board based on the example "asset_tracker_v2" and we are having issues with some SIM Cards.
We are using iBasis...
Hi! I am developing application for nrf52840 on nrf connect sdk 2.9.0. I am using mcuboot with serial transport as a bootloader. In bootloader I am using uart with hwfc and...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...
Hello Nordic team, We are using the nRF52833-QDAA SoC in our new project. While the chipset is advertising over BLE, we observed that the nRF Connect application displays...
Hello,
I have designed this schematic according to reference designs provided by Nordic Semi, however I might have failed as I am unable to flash the main module. I should...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello all,
I'm currently modifying my Analog Input circuit schematics to improve precision.
I'm adding after my voltage divider, an opamp as a voltage follower to ensure...
HI NORDIC TEAM
Hello!
Does the NORDIC chip support the BLUETOOTH 3D Synchronization Profile?
Are there any relevant documents or procedures that can be referred to?...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi,
I'm developing my app on nRF52840, NCS2.7.0 on VS Code 1.100.0.
My application needs to save settings data (4 x int32_t ) to external the NOR Flash (mx25r64) in `settings_storage...
Hi.
I have been investigating how to use GRTC and LFXO for LFCLK with nRF54L15DK. In my goal, I would like to make the Intermittent application with sleep and GRTC that...
Hello,
nRF Connect SDK v3.0.1 nRF54L15-DK v0.9.1
Currently, I’m exploring whether it’s possible to create a Bluetooth application that can be controlled from an external...
Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
I have just purchased nRF54L15 DK, run Quick Start and programmed 'Hello World', but the verification failed and nothing happened. I opened the serial terminal, but nothing...
