I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Easy task, and long way..
I need to counting/measuring time how long time 220V line was on-line (assumed all time after install).
I've tried to find ready-work chip FR-transmit...
hello I'm Mehdi. i work on two NRF24lL01 wireless modules. I have a doubt that this modules can be damaged or not work correctly. because the module don't give external interrupt...
Hi!
I am trying to make basic temperature nodes with nRF2402.
The receiver is nRF24L01 transceiver.
My question for nRF2402; is it possible to send config bits via...
Hello,
Recently I've begun updating to the new SoftDevice and SDK for the nRF51822. When I began debugging my migrated code with the development dongle and Master Control...
I'm looking for a little guidance in figuring out why I get this error now when I call SOFTDEVICE_HANDLER_INIT. It appears that I get the error above at the end of softdevice_handler_init...
Dear nordic guys,I'm developing with nrf51822.
I have one simple question.
I want trying to connection request at the BLE server side to BLE client with previous connected...
I noticed that m_sec_params passed to sd_ble_gap_authenticate(uint16_t conn_handle, ble_gap_sec_params_t const * const p_sec_params) has been declared as a static variable...
Hello
I was trying to make an example program for a Client. And when I was searching for the sd_ble_gap_scan_start function I didn't find it. Altough in the documentation...
I am getting an NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add. This is the 12th characteristic added and follows the same general style of numerous...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
Using these to build a project based on the sample proximity...
Hi,
I just tried to toggle a led when a particular button in the evaluation board (nrf51822) is pressed, i just referred the gpiote sample code and started modifying it...
Hello,
I'm working on the nrf51822 with s110 stack and 5.1 SDK.
Wy functions are not described in the documentation but just enums and data types ?
I'm looking for informations...
I'm wrote a simple test to persist data using pstorage.
But I'm unable to load the stored data.
I'm using gcc and debugging with gdb. So I can see that storage_cb_handler...
Hi,
I am working on a project where there are moving devices. Devices can only move if a wired button is pressed. In fact, for security reasons, there are two buttons connected...
I've been looking at this for the better part of a day and can't seem to pinpoint what I'm doing wrong here. Does anybody want to take a quick peek at this project and tell...