It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
I currently have a custom service emulating the batterey service. I have added an extra characteristic to recieve data from the central in the same way as ble_app_uart. the...
Like explained in this tutorial , on master control panel I do File-> Flash Programming and reprogram the dongle, which then turns on one more LED on the dongle. But, I still...
I'm using SDK 7.1, PCA10028 eval board, SD110, MCP 3.8.0.7
I've compiled and loaded the dfu_dual_bank_ble_s110 project into my PCA100028 board. It shows up in the MCP as...
Hey,
I use ESB protocol on nrf51822. I am using one Pipe currently I can achieve only 183 Kbps, I read that i can achieve 1Mbps data rate if we use ESB. I have few questions...
I understand that it is possible to set a static passkey on the nRF51822.
However, what I would like to do is handle the verification of the user-entered passkey myself...
Hello all,
I am completely new to BLE and would like to make a sensor network with nRF51822 ( 1x S120 as center node and 8x S110 as slaves) I have been reading the content...
I am trying to make my NRF 51 advertise forever till someone connects. I have based myself on the ble_uart example where it uses fast advertising with 40 ms intervals for...
Hi,
Last year, I heard that nordic semi will release a SoftDevice for central that supports mulitple packets per interval time until June, 2015.
For now, I guess s120...
My understanding so far is that the input buffer of GPIO is disconnected by default and we can keep it disconnected for saving power when the pin is configured as output....
Hello,
I just read this paper "High speed data streaming with nRF24L01 " where we can achieve 1.6 Mbps Data Rate in clean RF environment. I am currently using nrf51822 in...
The documentation for ble_evt_hdr_t says that the evt_len field is
Length in octets excluding this header.
However as far as I can tell it's actually the length...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I need to implement an application who acts like a GATT client and gets notification from a GATT Server (on smartphone) and then sends the information to a GATT Client...