Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
We would like to drive two ps/2 interfaces via nrf52840 gpio pins (i.e., reading the protocol bit by bit, via gpio interrupts). A trouble is that ps/2 is timing sensitive...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
Hi,
I am developing on nRF54L15-DK BM (bare metal) for another board with a different pinout.
I need to disable the the MCUMGR log that prints to UART TX pin 1. 04....
Hi,
I am working on Google fast pair locator tag using NCS sample code. For final product, we need one function in device for certification that is to disable and reenable...
Hi nordic support:
Our product used nRF52840, we tried test nRF52840's BLE OTA RF performance with CMW500. After the nRF52840 device is assembled with the casing, it is...
We have a custom nRF5340 board that interfaces with an MT29 NAND Flash IC over the SPIM3 peripheral. Our DFU solution involves storing update and rollback images on this external...
I'm developing on the nRF54L15-DK using NCS3.1.1. I've recently encountered a strange behavior.
My program writes to the RESETREAS register. A bus fault sometimes occurs...
Hello,
Following the ongoing many issues to make Ethernet work alongside the modem on nRF9160 ( , , devzone.nordicsemi.com/.../ (clicking “Convert to public” on this one...
Hi !
I've been through a lot of documentation but did not find any matching my case.
I'm using a custom board with an NRF9160 chosen for its ability to connect to LTE...
Hello,
I want to use P0.10 and P0.11 for SPI purpose for my custom nrf5340 board.
But when I clear the forwarder property for these pins from the pin editor gui, I am...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hi Support:
I am testing channel sounding initiator on our board, but there is a crash on CS initiator starting.
below is log:
uart:~$ initiator on [00:57:24.604,598...
Hello,
The Altium lib provided with the DK, has two geometries, one with an "_2" at the end, what is the difference between these? (if any).
Thank you,
Beleni...
