Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
I have received my NRF52840 DK V3 and i open NRF connect for Desktop and run "Quick Start", it have detect the board but when i try the hello world program test it is not...
Hi Nordic team, We have a project that uses nRF5340 &NCS 2.7.0, and we encountered net core crashing issue each time when ble is connected by central device and 5340 app core...
Description:
Hello,
I am trying to build my project nrf_dm_testing using NCS 2.9.0 , but I am encountering a CMake configuration error. The error message is as follows...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
I am using VS Code IDE and have installed nrf Connect Extension and done with the installation part and blinky and few other samples. So, basically I just copied an available...
I have figured out a way to realize IR communication,it is same with the way to drive WS2812 with SPI.
[ I can use PWM peripheral and should use it,for I need to change...
Just to confirm the head question.
I have found the same question : NRF52 help configuring TIMER + DMA + PWM - Nordic Q&A - Nordic DevZone - Nordic DevZone
There is no...
Hello,
1. Do you have any hardware to implement Wireless HID USB without Bluetooth like Logitech with USB dongle?
2. Do you have an example of IR TV remote for any hardware...
Hello,
NCS 2.9.0 nRF54L15 DK 0.9.1
I am trying to follow the instructions in the manual in the User Guide of the nRF54L15 DK to use P1.00 and P1.01 as normal GPIOs. (side...
Hello,
I have been following the steps in Exercise 1 of Lesson 1 of the Cellular IoT Fundamentals course. I have a Thingy:91. I have followed the steps so far
- flashed...
Hi
Long time no see
I recently got my sweaty hands on a sparkly new 54L15DK, and I thought I would try it out. The AI guided me to the coremark sample and the multicore...
I recently tired the Onomondo static and external softSim demo on the nRF9151 DK. For both of the demos they take around 4 minutes until the DK gets a cellular connection...
What is the connector cable that fits with nRF5340 DK J1, I am using the other end to connect to the ANT-B10 J2 (antenna board). I will like to know which connector cable...
