Hi,
I am currently trying to build the channel_sounding_ras_initiator sample without any changes. I was successfully able to build the channel_sounding_ras_reflector.
...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
I started with the template app and added BLE services, and I'm continuing by adding a TWI sensor (I2C). I know there is a TWI_sensor example, but I already had some working...
Dear All,
I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).
I downloaded SDK 15.3.0 ble_central...
Hello, I am evaluating ways to enter the DFU mode when application is corrupted (i.e. it does not reach the code for entering bootloader).
The documentation states that...
Hi
I'm working on a IoT solution with a small circular board, 26mm in diameter. I was suggested by Johanson to use the 2450AT18D0100 antenna and a lowpass filter designed...
Hi,
I am new to this nrf development, I have been working on the SDK 15.1 on the nrf52832, with softdevice 6.1. I found these examples in the SDK very helpful. I have to...
Hi,
I am planning to send an analog signal to the nrf52840 dongle pin and send it through bluetooth to mobile app. I am thinking of merging ble_app_rscs and saadc together...
The IP mode is IPv4.
1. The hostname resolves to IP address. The resolved IP address is correct (verified with a nslookup command separately).
2. setsockopt(fd, SOL_TLS...
I am implementing a serial transmitter using the nrf_serial library from the nRF5 SDK 15.3.0. The application is very similar to a serially addressable LED string.
My serial...
Hi,
i m using my custom nrf52832 beacon.For Battery power, i used accelerometer.i trying to change advertising interval for non connectable BLE device while accelerometer...
Now there is a project, nrf52840 uses SPI to communicate with other microcontrollers. Data is currently available, but it is suspected that each packet lacks a second byte...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
I am working on a ble nus pheripheral application on nrf52810 with sdk 15.2 and s112. currently I can connect to nrf52 with 4 mobile phone at same time and send&receive string...
I managed to set the UUID section on my own, but I'm having trouble reading and writing some data. I'm changing the on_write function in Ble_nus.c, but I can't get results...
Hello,
When debugging one of the projects, I encountered the situation of a frequent reset of the device during connection. A quick scan under the debugger helped show the...
Hello,
I'd like to develop and base on the " Experimental: ATT_MTU Throughput Example" project.
Seems like the example project doesn't implement the DFU (aka, OAD).
...
