Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Our repository is hosted at github and we are developing and building with Segger Embedded Studio.
Is there any documentation for setting up CI with github actions, travis...
is it possible to access application logs via the SWD interface?
For eg: i see code like NRF_LOG_INFO("Temperature example started.");
Can i see this just by connecting...
Hello everyone.
I use nRF52840 and Segger Embedded Studio. This is my first MCU development.
Thanks to the SDK, I was able to use GPIO, twi, etc.
I am interested in...
We have noticed that using nrfjprog for programming 52840 based devices (and the devkit) that programming times are longer than with 52832 based devices with the same size...
I am trying to switch leds on and off on my nrf51822 beacon kit using an android application to be made by me.
I am not able to get any similar example.
Also i want to...
Hello,
I am not able to get the UART DFU secure bootloader example work for PCA10040 nRF52DK.
I have flashed the device with Bootloader and SotDevice 6.1.1 version.
...
Hello, I am a newb currently working to be able to send and receive timestamps between two nrf52840 dk's.
I have been successful in creating a space in the advertising packets...
Hello, I am developing a Python script (Windows 10, Python 2.7.16, pc-ble-driver-py 0.12.0) to use a NRF52840 board to simulate the BLE part of an application running on a...
Hi,
I'm working on the nrf52832 development board and SDK 16.0. I want to use the Power supply supervisory functionality to detect any type of power failure.
I'm using...
Hi,
The example is currently printing the device address
on_adv_report(ble_gap_evt_adv_report_t const * p_adv_report) { ... NRF_LOG_INFO("Connecting to target %02x%02x...
I am going to find out an ideal throughput of NRF52832. And my environment is NRF52832/S332/MTU 247/connect interval 20ms.
Finally, i got a maximum value about 23Kb/s. I...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
