I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I'm developing firmware for nRF52832 with FreeRTOS, I would like to use TWI to access to an external memory. Every time I try to use "nrf_drv_twi_tx" function i get...
Hello,
Is it possible to get more information on how the NWK Frame counter is stored in NVRAM. I can see fragments of code from zb_nrf52_nvram.c I see that it uses nrf_fstorage_write...
I am facing an issue in writing data to a register of my bmp388 sensor using I2C.
If I fill my transmit buffer of 2 bytes in following way , tx_buf[] = {register_address...
hi support team,
i was testing this this example " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.4.0/nrf/samples/nrf5340/netboot/README.html#nc-bootloader "
i...
Hello all,
We are trying to implement coexistence between BLE and Bluetooth mesh.
After following the Nordic coexistence tutorials, our program builds fine using both...
I have worked with the nRF51822 and the nRF51 DK and used the pc-ble-driver on the nRF52840 dongle. Now all I am interested in the BTLE development, not mesh. I found out...
Hi
I did some experiments with the GATT capabilities of the S140 7.2.0 softdevice. An experiment that I did showed a behavior that is not as I would expect it.
Steps to...
hi professor,
I use the zephyr spi driver to control spi nand flash.I want to send two bytes and read 3 bytes. But between write and read time sequence there are 10us delay...
I'm testing nRF Mesh on nRF52840 chip, I used P1.10 for LNA pin and P1.13 for PA pin, I tried to config but it not worked. how to fix it?
static mesh_pa_lna_gpiote_params_t...
Dear support team
Please note my sample application code attached, and the trace of the I2C transmission
I am facing the issue that the twi driver does not write more...
Now I am using nRF52840 I want to get data from a sensor via SPI. I configured the SPI pins like this P0.11 -> SPI_CS P0.12 -> SPI_MOSI
Actually, I couldn't get any data...
Hi Nordic-Support,
I am trying to figure out how the boards in ncs/nrf (e.g. thingy91_nrf9160) are made available for applications. I cannot see how they are added to the...
Hello,
I would like to take a photo and send it via Zigbee to another on nRF52840. Just a single image that is around 600x480 sizes. What interfaces can I use for that purpose...
