hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I successfully compiled and loaded the UART/Serial Port Emulation over BLE example on an AdaFruit Feather board.
I can connect to the Nordic UART Service, then send data...
I have built my application on ble_app_uart in keil in SDK 14, so I just did the same and copy-pasted my code into the latest ble_app_uart example built with ses in SDK 16...
So far i've failed to find a single source that contains comprehensive information on where errata items have been addressed. I do have multiple unrelated sources for information...
Hello, I want to try the secure bootloader + softdevice 7.0.1 + ble app buttonless dfu example from SDK16 I want to test all that in our custom board NRF52832-QFAB (256k flash...
Hello, I modified the ble_app_blinky example to work on our board (removed leds and buttons) and modified the board pca10040.h the new application worked on the devkit but...
Hello, I am completely new to embedded software development (so far I have been using development boards such as Teensy, Feather and Arduino) and I recently acquired the BLYST...
Hi
I'm currently look into the noise floor of the SAADC samples on a custom PCB with a nRF52
I'm running the ADC at maximum sensitivity (4x gain, Vref=0.6V) differential...
Hello
I have a power constraint device. Limit is not the total charge of a battery or so. Limit is the peak current.
Available (peak) current is around 4mA (@1.8V), current...
Hi,all. i face a problem that i used lightblue on iphone6(ios8.3 12F70) to connect my device(nRF51822),after sometime,disconnected automatic.
lightblue says:The connection...
Hello Community,
does an opened timeslot session affect my power consumption?
I need a cyclic timeslot for my application and I'm wondering wether it generates an incrased...
Dear team:
I have a question with nRF52832 XATL 32.768K. When I used 13 GPIO to be a interruption，the internal clock delay was more slow than before。what was wrong with...
I am not able to send ble_nus_string_send 8th time when I am calling it for 8th time. That is it is sending 140 characters. I am sending data from nRF51822 using ble_nus_string_send...
Try as I might all searches for anything related to sd_rpc_* give 'no results'. Admittedly the search engine for the online and offline documentation is poor/difficult to...
Hello,
On our current hardware there are no IO pins left to add any dedicated U(S)ART connectivity. Therefor is there a way to perform any kind of serial monitoring via...
