Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hi,
I tried the nrf51_iot_sdk_0.8.0_f1f6187 and flashed the coap example (examples\iot\coap\ipv6\client\boards\pca10028\armgcc) with the s1xx-iot-prototype2_softdevice...
Hi,
In many places in the nRF51 documentation (e.g. developer.nordicsemi.com/.../a00081.html) the term "Master Control Panel" is used without clarification that this is...
Hi:
i use SDK7.0 , i write data in flash (address:0x0003fc00)and the data is erased when SDK run.
and is there any way to protect the page that i want to write or...
Any recommendations of power ic to be used in an nRF52 based system?
I am thinking of using DC-DC converter from LTC3553 . Is DCDC converters a good choice for powering nRF52...
Hello,
I am basing a design on the reference design from the nRF-DK (pca10028?). I am trying to understand the implications of using an SMA connector footprint for testing...
I tried to get the ANT background scanning example to work on a PCA10028 and it jumps to softdevice_assert_callback when opening the ant channel. Downloaded everything fresh...
Hi Guys,
I'm new to using the nRF51822 environment but I've used AVRs for years, so please be gentle...
I'm wanting to drive a strip of WS2812 RGB LEDs from an nRF51822...
So I have my nRF51822 updating the characteristic value and sending notifications once every time I receive a radio notification.
uint8_t readings[20] = { 0, 0, 1, 2, 3...
I'm trying to set up TIMER0 to interrupt the timeslot 500us before its end.
It doesn't seem like the NRF_RADIO_CALLBACK_SIGNAL_TYPE_TIMER0 signal is happening, I've put a...
When I try to enable SD having earlier initialized Gazell (SD resources variant) sd_ble_enable() returns 2 (SOFTDEVICE_NOT_ENABLED). If I remove the Gazell initializaton it...
I am trying to work with a custom 3rd party BT 4.0 peripheral device which uses an nRF8001 to transmit data as temperature values in the Bluetooth Health Thermometer service...
Hi,
Slight problem here with bootloader updates : right after download, I copy from SWAP (0x16000) to normal location (0x38000 in my case).
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;...
I am wondering how to precisely measure my power consumption. Till now, I have been using INA216 on PCA10004 board + labView for acquisition, but it is not precise enough...
