Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hello,
I am experiencing a critical failure while trying to program my nRF5340 DK using the nRF Connect for Desktop Quick Start app (v1.6.0). The process fails at the "Program...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I have successfully installed west and zephyr, and I have successfully build a simple tflite-micro hello_world example, but it just generates the zephyr.hex file. SInce i...
I am using a dynamic BAS service. I have noticed that after a few bt_gatt_service_unregister() and bt_gatt_service_register() calls, the following error occurs: bt_gatt: Unable...
Hi, trying to directly build the solution for the exercise i get this error at the end.
The whole log-output:
Building l5_e1_sol west build --build-dir /mnt/df01dc22-f3bf...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Cannot program our nRF9151-SMA-DK, we have other boards and work normaly. This is the programmer log:
08:30:21.996
Initialising the bundled nrfutil device
08...
nRF54L15 - ncs 3.02 - toolchain 3.02
I changed my build settings from no sysbuild to sysbuild in order to use serial recovery and/or FOTA. I thought everything was OK until...
Hi,
For my university MEng group project, I am working with the nRF5340 Audio DK and Bluetooth LE Audio (LC3 over ISO).
My end goal is to stream audio from an nRF5340...
hi,
i'm a beginner for nrf9160DK so can you guys help me to how can i nrf9160 up and running for the first time. i'm not able to up and running with this video https://www...
I have a problem where the GPIO pin is not working as intended (it is constantly high but it should be alternating high and low). Via debugging I've ascertained that the problem...
Hello, I am encountering a crash in MCUBoot when using the following configuration:
MCUBoot as bootloader (SB_CONFIG_BOOTLOADER_MCUBOOT)
TFM configuration (build /ns...
I am encountering a build error while setting up a build environment. Can you provide assistance as to what the issue I am encountering may be? I am using VSCode on MacOS...
hi,
i'm stuck at lesson 3 exercise 1 in step 1 so i create an application with choosing option 1 create a blank application for this first task to print hello world and...
Exhausted everything. Here's the guts of the code. A task is called at 2Hz to push the value, which at 1024/s makes an event time of +512. I set the cumulative RPM to +1 for...
