Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
Hello,
I am trying to test BLE with SAADC, UART function.
I am complete the ADC test and UART part.
So now, I want to SAADC with BLE and BLE with UART.
The whole connection...
Hi all,
I tried to follow this tutorial to be able to use GDB as debugger but failed right in the beginning because JLinkGDBServer could not connect. Here's the log I get...
Hi , i am using the nrf52dk and i have a switch statement that depending on the case there is a set of enum and i would like to utalised the push button to increase/decrease...
sir, i am attempting to compile a solution from github(nrf calender) but i could n"t.Tell me where should i put the file and how to compile to make it work??
Hello,
I have a question: how can i make applications for Nordic Thingy:91, and upload them to it? (I am a total newbie when it comes to Nordic products and IoT, i am not...
Hi All,
I am developing one project and there we are using ADC (i.e., SAADC in nRF). I have designed the hardware where I am using Capacitor ( C14, 2.2µF) which is connected...
Hi. I have a nRF52840 setup using the PWM driver, and it is outputting a 50Khz pulse 50% duty cycle.
How do I modify the sequence values so that I can modulate this 50Khz...
Dear all,
I would like to implement the IEEE 802.15.4 stack, using the driver inside the SDK for Thread and Zigbee. Unfortunately there aren't any examples ad so everything...
Hi! Please, excuse the probably stupid question but I'm a real newbie. I'm trying to perform a long range coverage test. I got two NRF52840 DK. Got to install both Segger...
Hello all,
I have a question about nRF52832.
What I want to do is increase a number every 20 micro seconds.
In other words, count how much time has passed .
(ex...
I’m developing a wireless sensor based on MINEW nRF52832 modules.
I use SDK 16 and SEGGER embedded studio.
The target is powered by a 3.6V Lithium Thionil battery via...
Hello,
I have been trying to setup timer counter for nrf9160dk using the sample I have attached but for some reason the timer value is always read as 0. Not sure if the...
