Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have a simple custom board using Fanstel BM15C module. It is connected to DEBUG OUT connector of the nrf54l15-dk.
I am using VS Code and nRF Connect extension pack, SDK...
Hello
since i could not post a ticket (got the message 'could not create a ticket'), I try it again with almost no text here but added the content in a txt-file.
Hope...
Dear Nordic-Team,
we are currently trying to add CSR creation to our project which worked quite fine by implementing it similar to the psa_crypto sample.
Unfortunately...
Hello Nordic Team, We are developing a wearable health device using the nRF5340-DK and Zephyr RTOS. As part of the BLE communication design, we intend to use **Security Level...
I am looking at options to integrate the ADXL 367 accelerometer into my firmware project (nRF Connect SDK 3.0.2). I see the sensor is supported by Zephyr and has a complex...
We are hardware manufacturing company currently developing AMI solutions with Wirepas integration. Do any of your partners offer smart meter solutions that use Wirepas and...
Before i inserted in my code to use ppi + gpiote + spim usb serial device port worked properly, it connected normally, but now it doesn't connect the port at all, did i create...
Hello, I am working on a custom board with my own custom project/application. I have recently done porting from ncs v2.7.0 to v3.0.2 - I was able to initialise the wifi driver...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Dear Team,
I would like to know if it is possible to add custom attributes and commands to standard clusters, such as the Occupancy cluster. I have reviewed the "Adding...
Hi everyone—I'm working with the Nordic nRF54L15 SoC , but I'm struggling to find guidance on using a chip antenna (design and components) . The official materials (e.g.,...
Hi Team,
I’m facing an issue when trying to perform BLE FOTA with a 2 MB external SPI flash (SPI4) as the secondary slot for MCUboot.
My setup works fine when using a...
Hello,
sorry, do not know where to file a bug.
Bug is, that nrf_radio_subscribe_get() and nrf_radio_publish_get() use the wrong offset (0x80) instead of the correct one...
Hi, I’m currently testing the update process via BT SMP on the matter window covering example (NCS 3.0.2, nrf5340). For my test, I created two versions: 1. Project with -DCONFIG_CHIP_DFU_OVER_BT_SMP...
