Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Wireless Communication Synchronization System Based on the Alignment Principle
A year ago, I proposed the wireless communication synchronization system described below....
I am going through Lesson 9 of the nRF Connect SDK Intermediate course to understand how DFU and FOTA work in the SDK. I am using toolchain and SDK v3.1.0, and nRF Connect...
Testing a new nRF9151 device using a project derived from the Nordic "HTTPS client" sample project. We are experiencing a "Modem has crashed" event intermittently when running...
Hi，
Background Information:
Our product, BLE near-infrared device , is undergoing CRA (Cyber Resilience Act) compliance assessment—specifically for the EU RED Cybersecurity...
This seems like a silly issue, but I cannot get the UART output from the nRF9151 DK. Attached is a project that outputs via both LOG and printk() to a Segger RTT viewer without...
Hello,
I am working on a simple Bluetooth Mesh application for light control.
I started from the provided samples: - github.com/.../light - github.com/.../light_switch...
I am trying to program an external board using the development kid following the instructions HERE .
I am using the debug out P20.
I have tried supplying the board frm...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
i built a small breakout board for npm1300 (QEAAD0 2516AA) to experiment with it. the twi pins are wired to the i2c ports of a raspberry pi 4 to control it, and i have attached...
I do measure different values for source and ampere mode. On the nRF52 DK. Source Mode: disconnect SB9, Power Switch is off. Vout from PPK2 connected to nRF current measurement...
Hello,
We are using NRF5340 in our product and running automated hardware testing. As part of this process, we need to program the chip twice: once with a dedicated testing...
Hello,
I am using nrf52833-dk for making a ZigBee coordinator. I am using "network coordinator" sample code.
The project is making a ZigBee connection between "nrf52833...
My error message is that it works on a computer, but it doesn't work on the company computer. I'm not sure if it's the encryption software on the company computer, but I don...
I have a 5 year old design using a nrf52832 on a MDBT42Q module. The BLE option was placed on the PCB in 2020 and has been unoccupied since going into production. My customer...
Hello,
I am trying to build the sample/sensor/lps22hh project on nRF52840 DK and STEVAL-MKI220V1, but receive errors in build.
I have added an overlay file as in boards...
