We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello, I just had a look at the Thingy:91 X with the nRF9151 and nRF5340 SoC's including nRF7002 Wifi support.
My understanding is that the nRF5340 is the main MCU running...
Hello,
We are in the feasibility stage of a product that requires integration of both the Apple "Find My" and Google "Find My Device" technologies.
Based on my research...
hi
We are developing with Segger embedded studio.
.
If you copy and move the SW development project folder to another PC, the following error occurs.
(Only occurs...
Hi,
Very beginner to this so bear with me.
we are testing an asset tracker which uses edrx. The asset tracker can receive a wake-up sms command.
However the network...
Hi,
I have ported my already working nRF52840 SPI slave code to a nRF5340, but it doesnt seem to receive any data. I have verified the CS, SCK and MOSI signals, but no MISO...
Hi,
I was wondering, what is the professional, assembly line ready procedure to program the IMEI on an nrf9161?
So far, I've only found rajeev's post in this discussion...
Hello,
I am using a Raytac MDBT50Q (nRF52840) on a custom board , and I am trying to blink an LED, but it is not working.
"I need urgent help as this is blocking my...
We can get BLE address in adv report: How to get mac address of nearby ble devices? - Nordic Q&A - Nordic DevZone - Nordic DevZone
At that moment, peripheral not connected...
I have download this .zip from the Nordic site. I am a beginning coder and I am using AI to help assist me on my project and learning C code. I seem to unzip the file correctly...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
