Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I made a custom PCB with the NRF52840-CKAA and the same 8MB flash memory chip as the PCA10056 NRF528040DK
I used the MX25R6435FZAIL0 because the MX25R6435FZNIL0 was not...
Dear Nordic Team,
After gaining experience with 3G and later 4G LTE-M over the past few years, I have observed a significant gap in the deployment of LTE-M in many countries...
In my NRF52840 based device using NRF5 SDK 17.1.0, I notice that sometimes this loop in the nrfx usbd driver code of the SDK doesn't finish:
[modules/nrfx/drivers/src/nrfx_usbd...
How can I please analyse the latency, reachability and throughput of the DECT NR+ on the nRF9161-DK. I urgently need a solution please, it's for my bachelor thesis. Thanks...
Hi, Im designing a custom board using a NRF9160 MCU. From the product specification it operates at a voltage range of 3.0(2.8)-5.5V. I want to use a 3xLI socl2 3.6v (parallel...
I created a blinky example in zephyr and created my board with Create a new board The build goes well and runs well. The problem is that the device tree gui does not run and...
Hi,
SoC: nrf52840 Environment: nRF Connect SDK v2.4.1
When performing OTA app upgrade all settings and bonds are gone. Settings subsystem seems to be working fine. Settings...
Hello,
I am currently working with the NRF52840 Dongle and have integrated a W25Q512 QSPI Flash chip, connected to the following pins:
CSN: P0.17
SCK: P0.20
IO0...
Hi
I want to know how to get a configuration of a single pin .
I added this function to the blinky example.
But it keeps reporting -ENOSYS.
Testing environment:...
Hi,
I have an application based on the "peripheral_uart" sample code (nRF52840DK, NCS2.70)
As I use interchangeably the same pins as GPIOs and UARTE1, I use UARTE1 with...
Hello,
I been struggling with this issue for a couple of days and can't manage to find the reason behind it.
About the project:
We are developing a IoT device firmware...
Hello all,
i have a problem and I hope that someone can help me.
I can change the bluetooth address of the device with the following code:
and this is okay.
I have...
I work test program on ncs2.8.0.
I put a reference to the BOARD variable at the top of my project's CMakeLists.txt.
When "west build -b nrf52833dk_nrf52833", BOARD is...
Can 52840 dongle program as BLE adapter for development usage like the following URL? Just for development test, so I don't need to buy one.
https://www.amazon.com/ASUS...
I am trying to build the Peripheral UART sample in nRF Connect SDK v2.8.0 targeting the nRF52805 SoC using VSCode. The sample is too large for the nRF52805 flash (linker overflow...
