Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,I am using NRF5340 AUDIO DK BOARD and I have been trying to access i2s mic and I want to transfer the mic data to Amplifier .Is it possible to do with single I2s ? As I...
Hello everyone,
I'm experiencing some issues while trying to program an nRF52832 CIIA on a custom PCB. Specifically, I cannot get the GPIO pins or the external 32kHz crystal...
Hi, I checked DFU over Wi-Fi in a separate project (net/download) that only included DFU and Wi-Fi-related functionality. In which FOTA is working as expected.
In our custom...
I have just started programming the using the nrf52840DK_nrf52840. I downloaded the toolchain and sdk using the VS code extension and created a new application from the blinky...
Hello,
I just upgraded from v2.5.0 to v2.7.0 of the SDK. To do this, I had to modify my files of my specific board and use sysbuild.
My project compiles and works on my...
Hi All,
I'm considering using the nRF5340 in an audio application. I'd probably go for a 3rd party module in order to avoid getting FCC certs on my own. Possibly the Fanstel...
In Section 6.17.1, page 543, of the nRF52840 product specification version 1.10, in regard to the Pulse-Width Modulation (PWM) peripheral, there is a statement that says ...
Good morning,
I am try to build a application from example list, Bosh bme680 with supported board rak4631_nrf52840, and I am receiving a error message, but if I try to...
hi ,
I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio (version 5.42a) as my IDE. I have successfully integrated the Timer...
Hello
I want to make an application based on the multi NUS sample https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/enter-the-multi-nus-a-simple...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...
I'm using a modified "HTTPS client sample" from nrf/samples/net/https_client in ncs v2.6.1 on the nrf9160dk board. The base example worked great and I am able to perform the...
Hi,
i use the nrf52833dk with ncs 2.6.0 and the official peripheral_uart example to test NUS. When i use my new Galaxy Tab A8 (Android14) and try to connect to the board...
Hello,
I'm working with the npm1300, and I was recently trying to implement sleep/hibernate mode. The datasheet states that before entering these modes we should check if...
Hi, we are trying to switch our nRF9160 project over to using HWMv2. We get a linker error that we are unable to solve. We think it is the combination between using our own...
