I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I'm currently testing BLE Coded PHY by using extended advertising.
I used two nRF52840-DK and nRF5 SDK v17 with compatible softDevice.
I've checked that the...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
I had a project that I made with SDK v2.6.0 and Toolchain v2.6.0 with an Actinius Icarus board.
Today I wanted to continue with my project so I build it and everything was...
Hi, We're using the nrf9160 with ncs 2.7, modem FW 1.3.6 We're trying to send an HTTP request with TLS 1.2. We have provisioned our device and verified the key,cert with a...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
Hi,
I still have problems understanding the port and pin assignment for peripherals on the nrf54L15.
I need up to three SPIM, one UART and one TWI. That should work, right...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hi,
I'm working on an nRF5340 + nRF7002 project using Zephyr RTOS , where the device enters low-power sleep and wakes up on a hardware counter alarm ( counter_set_channel_alarm...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
