Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I am using the nPM2100 EK dev board with a stm32wl5MOC.
Using the example from the bare metal drivers, I adapted the code to my board.
I can succesfully read and set bytes...
currently this is more of a theoretical question, but i have an idea of something that might utilize this (3 QSPI devices)
Ive been looking at the Nrf5340 and the nrf7002...
Hi, I am stuck on the BLE channel sounding Initiator initialization. I took the code from the channel sounding connected initiator and integrated into my FW.
Due to unknown...
Hello Nordic Team,
I am using the nRF5340 Audio DK and I want to implement a simple audio loopback — where the board captures voice from the on-board PDM microphone and...
hello~
nPM1304 nominal sleep mode 500nA (it is still uncertain whether the buck converter can operate?)
Can't the sleep mode be lower than 500nA?
best regards
sam
I'm following the Lesson 9, Exercise 2: DFU over USB - Adding External Flash from the Nordic Academy: Tutorial Link
SoC: nrf54l15
SDK version: 3.0.2
Toolchain version...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
Hi,
We are using the PMIC in our smart ring where we have limitations of number of components used and specially the height of the components used. Here, the inductor...
Dear Nordic Support Team,
Hope this email finds you well. I am currently developing a Matter-enabled device using the Nordic nRF Connect SDK, and I’ve encountered a question...
