Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello Community,
I have nRF52840 board. When I connect board to system it not get detected.
I tested VCC supply it is OK.
COM port is not seen anymore.
I tried to...
Hi Sir/Madam,
Our application needs to be running on both cores and the network core needs to use some crypto algorithms provided by the crypto cell. From the data sheet...
Hi, dear Nordic & all：
I found nrfx_saadc_uninit() did not work when use SAADC's differential mode with SDK17.0.2, nrf52832, the fellowing is saadc init and configuration...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add Just-Works bonding function. But this bonding request need launch...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_template_c but when i run the code i get the following below error are as follows...
Hello,
I am compiling my BLE project on nRF5340, with nRF Connect SDK v1.6.1. I got this error: undefined reference to bt_gatt_exchange_mtu.
My code works fine on SDK...
11:14:55.624
Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED, message: 'No response from device. Tried to send packet 6 times.'
11:14:55.954
Server setup...
Hello,
I am looking at the Asset Tracker v2 example and was wondering if it is possible to use the A-GPS or P-GPS services offered through nRF Cloud if I am using AWS or...
Hello,
Both parts part#nRF9160-SICA-R and nRF9160-DK are available on Mouser website but t he customer would like to check what revision is.
Could you please help to...
Also please let us know if there are any antenna design specifications.
If we use other antenna for NFC is your certification valid or we need to re-certify our product...
Hi,
I've been experiencing some very slow erase times in the erasing / programming stage. Consistently around 10s. I am using SEGGER Embedded Studio, J-Link V7.22, and...
Hi all
According to the PS of the nRF52832, the INFO.VARIANT field in the FICR is ASCII encoded (e.g. 0x41414530 -> AAE0).
Are only capital letters ('A' - 'Z') and numbers...
Hi everyone,
My task is make Uart peripheal advertisments on coded phy, for that i CONFIG_BT_EXT_ADV=1 on autoconfig.h, and I add the function bt_ready of the project peripheral_hr_coded...
