Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I try sdk 17.02 nRF52840 usb audio demo, I want to achieve 48KHz stereo music play by a I2S DAC.
Because I need to compress data in main while(1) loop, I found that...
Hi,
I'm little confused regarding BLE NUS and characteristics.
I know that the characteristics are used to expose data, but we also have BLE nus which is used to send...
Hello,
I have 2 questions:
1. Could you tell me the current consumption of a nRF52832 running RTC with external 32 kHz crystal and no RAM retention? Is it 1.9 µA?
...
Hello,
I use nrf52840-dk as central_hr and nrf52833-dk as peripheral_hr, examples from NRF Connect SDK.
It works well, but I want to implement reading Device Information...
I got following error when use the Command Prompt feature
After i run "ncsmgr init-ncs" from bash, it shows
$ ncsmgr init-ncs Checking out NCS v1.6.0 ...FATAL ERROR...
Hi,
I'm developing with 52840 DK, trying to add peer manager to another project I've modified from ble_app_uart (basically I've added saadc, SPI, USB and I2C module based...
Hello
I was setting up the nordic thing 91 (1.4.0, 2020.23) using this video https://www.youtube.com/watch?v=xQ7hDzRULJQ&ab_channel=NordicSemiconductor .
Things were...
I'm starting to design a custom board around the NRF52820 using a 3.7v battery and there is no reference circuity for VDDH using Battery/Ext. regulator. Any tips on what I...
Hi,
We are in the process of evaluating coded phy transceiver for our next product. The product is a IoT node which will send sensor data to centralized gateway and will...
I am using nrf_drv_twi_rx to initiate an I2C read transfer but the interrupt isn't fired for the RX transfer when the ulTaskNotifyTake is used, but seems to work without ulTaskNotifyTake...
Hello, I am making a system with 20 peripherals to a central base on nRF52840. I followed the firmware."ble_app_uart__saadc_timer_driven__scan_mode" from NORDIC playground...
Hello, i I am designing a prototype, the goal is to be able to control a small engine. This engine will be activated when a message is received in MQTT. I currently succeeded...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. I have now two questions: - is ZigBee 3.0 supported by...
I'm currently working on the nrf52832_qfax_dcdc pcb after adding a few components. I need to route to pins p0.22, p0.23 SWDIO and SWDCLK but am unable to route away from the...
