We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Dear Nordic support,
I was reading the Technical Documentation in the GPIO section for the nRF9151 , and I came across this blurb:
"Note: When a pin is configured as digital...
nrf5340 - running the complete BLE advertising and handling the read / write gatt client processing running in network core and doing rpc to application core
Create a sample...
Hi
I have questions about nPM1300 VOUT1 inductor
1. Our load current for VOUT1 will be <20mA, so could we use below inductor?
2. Datasheet 6.3.5 define it's recommended...
Hello
I would like to use the SPI to communicate with an IC without having a software driver.
I have the following device tree:
& spi2 {
compatible = "nordic,nrf...
Hello,
We are using nrf52dk, with zephyr OS also we have done the setup in VS code with extension.
Toolchain version: v2.9.0
SDK version: 3.7.99-ncs2, these all came...
Dear all,
I'm having difficulties scanning as a central device showing the short /long names like e.g. "Polar H10 xxxxxxxx" I can see the names when scanning on my smart...
Hi,
We recently managed to get the onomondo softsim working on a dev kit, we used the sample code provided by onomodo to do this. Now we want to add the softsim to the nrf_cloud_multi_service...
Hi everybody,
I have problem with my nrf9151-DK and attemp to create PPP communication.
First of all, I have to say that I am a beginner in this matter. I haven't come...
Hi,
I'm new to the nRF52840 and BLE and want to send a simple string like "Hello World!" to a paired device (phone) at a cadance of 1Hz e.g. I started with the peripheral...
Does anyone have experience with using a TP4057 with the nRF5340 for charging and fuel gauging? I watched Adding battery charging and fuel gauging to your nRF52 Series project...
Hello,
I am using the nRF52832 WLCSP with the imprint "N52832 CIAAE0 2207A5", and my FICR reports a codepage size ox 0x400 and a code size of 0x100. This results in a...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
I am using the Nordic Mesh Library with an ESP32 IDF-based application on the ESP32 side, and I am using ESP32 BLE Mesh. On the Android side, I have created a node to send...
Hi,
We are using the nRF52832 in a battery such that we have a 3V3 LDO configured to turn off under a certain battery voltage. Now during testing we have discovered that...
Hi,
I have made my own custom board with the nrf52811. Therefore I was using the nrf52dk.
I have made connection with my custom board and simply want to blink an led....
