Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
hi everyone
i need some help, when i scan my device with my smartphone every things is well but there is something weird i usually find two services with the same uuid instead...
Hi,
I'm wondering if your SDK15 and S140 v6.0 will have support for your IOT SDK when it is released? If so, will it also include examples for nrf52840?
Thank you
...
I tried to use UART both for NRF_LOG and NRF_CLI. Now it's running but I had a problem that calling to nrf_cli_init caused fatal error 8 - INVALID_STATE.
When I commented...
i have question about nRF52832's bluetuth. xtal is 32M, Cload is 12pf, but the frequency is 2.402199G(tested by Network Analyzer), Frequency differency is 199K. We find that...
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
I am trying to run pb remote example but i'm stuck at command 3 it only shows "Got event 0" not goes further to receive remote uuid.
0> 1) Provision first available device...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
