Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
Hello,
Is there examples of paring,bonding and whitelisting?
The pairing and bonding mode is static password.
It is best to have examples of the central and the peripheral...
Hi Nodic support team.
I am using esb_ptx and esb_prx for testing interface.
Can i change nrf_esb_payload_t.data in receiver of esb_prx?
It is always 8 bytes even though...
Hello everyone,
I followed the guide from this site to connect an Adafruit PN532 to an NRF52840
and tried running the adafruit_tag_reader example from the SDK.
However...
I implemented firmware update over LTE Cat-M and Ethernet last year by modifying the `fota_download` and the `download_client` examples into my own slightly modified version...
Hi,
I am using nRF52833-DK connected to my PC with usb cable for programming and debugging using the on board jtag.
In the beginning all worked ok, suddenly the jtag stopped...
Hi，
I have a custom board with nRF52833 and sky85303-21 FEM. To control the FEM, I have added the following code to my app.overlay file and enabled simple GPIO configs....
Hi everyone,
I'm encountering difficulties running my application on a custom nRF52840 board with a 48-pin package using Zephyr NCS version 2. 4. 4 in VS Code.
The problem...
Hi
Iam trying to make an ble advertiser project on nrf52840 with nrf21540(custom board)
there are a few configuration changes required for the board(pins and supply voltage...
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Earlier I was using nRFconnect SDK 2.1.2. Everything works perfectly fine with that. Many features were added in that project. Now I want to port my project to latest SDK...
Hi Everyone
I'm developing a project using NRF52840 , the application needs OTA over BLE . It was working before without no issue , we tested in many devices and many times...
Hi,
I'm wondering if I'm missing something. I've been creating a bluetooth mesh light with hue, saturation, brightness, on/off, etc. models. However, my model_handler.c...
I have an app that uses the Nordic IOS-DFU-LIBRARY to drive the OTA DFU process with an Adafruit nrf52840 Feather running the Adafruit bootloader. I have the library setup...
