Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Below is my change, set options to BT_LE_PER_ADV_OPT_USE_TX_POWER
But it always display Failed to set periodic advertising parameters (err -5) , why?
My hardware is...
Hi again,
I'm having trouble with the Matter Test Harness. I have been running tests in isolation one by one and fixing issues the TH finds. Now I have run into an issue...
Hi,
toolchain:-v3.1.0,sdk:v3.1.0. i am using the vscode software for the development
Basically i am trying to connect the peripheral using the address (mac:- 7C:D9:F4...
Hello,
I am using NRF5340-DK for my project and I wanted to know if there is some example on how to read and extract the public key from this type of certificate. I have...
hi support team,
i am trying to help customer on demo about 9151 dfu 52840.
currently, 9151 is using nrf_cloud_rest_fota demo and 52840 is using "zephyr\samples\subsys...
I am able to successfully perform a firmware upgrade on the Distributor itself. However, when attempting to upgrade the Target devices, the mobile app shows Upload Complete...
Using the latest version of nRF Connect for VS Code, how can I display all output lines of the build process rather than the “condensed” line overwriting version. This used...
I'm seeing a few of these errors in my uart evt handler
I cannot seem to find where these are enumerated in app_uart_fifo.c or nnrf_drv_uart.h or nrfx_uarte.h.
Question...
Hi,
I have just received 2 DK boards for the nRF54L15 and using VScode to build and flash the code onto the DK
The reflector is detectable on my phone and I can connect...
SDK: nRF Connect SDK v2.9.0
Chipset: nRF52840
I'm using ncsv2.9.0nrfsamplesperipheralradio_test to test the RF.
The initialization code is as follows:
At this...
We have a custom board with npm1300 seem below. Im loosing 3mA more than expected. I used npm1300 both Vout1 and Vout2 before in other project. Same design and copmonents...
Dear Sir and Madam,
Now we are trying to certify Bluetooth qualification for our wireless module used nRF54L15, we are considering how we can set TSPX_FAE identifier?...
Hi Team,
I'm trying to calculate CMAC using the KMU on the nRF54L15, but the `psa_mac_compute()` function fails with the error code `PSA_ERROR_NOT_PERMITTED (-133)`. I need...
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
in my disc, C:\ncs\v3.0.0 is here. but in nrf extension, weclome page shows the button ("install sdk"). it looks find no sdk. I need set the path to C:\ncs\v3.0.0 (I do not...
