Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello. I'm a newbie and just starting to learn the nordic SDK.
When doing the exercise in DevAcademy - ncs_fund v2.9.0-v2.7.0 l2_e1, I came across the fact that nrf Kconfig...
Hi,
I have a Thingy:91 with asset tracker v2 installed on it, and I am a bit puzzled about the results I see based on the configuration. Let me list some information.
...
This is likely a Visual Studio issue but figured this is an obvious rookie error so someone will set me straight right away! I have loaded a sample project and compiled and...
Hello, I am working on a project that is in charge of measuring temperature and sending values via BLE. I am working with the DS18B20 sensor and I have helped myself a lot...
Im trying to use lvgl with ST7789v display and nRF52832, in nRF Connect.
My .overlay:
My prj.conf:
When I enable LVGL and build, i got the error:
Could...
Hi,
I´m tryng to developer an application with nrf9161dk and i need create and upload a txt file with FTP. I´m in trouble to create the file with <zephyr/fs/fs.h> and...
Hi,
Your Dev Academy email-verification system may be broken, or I am broken :-)
After submitting the sign-up form, I am told to check my email to complete my registration...
Hi,
I tried the subsys/usb/console sample with nrf7002dk and I have ttyACM2. docs.nordicsemi.com/.../README.html
I copy the prj.conf to the end of the prj.conf of the...
Hello,
I am attempting to connect to a Wi-Fi network using Exercise 2 from Lesson 2 of the Wi-Fi training in Nordic Academy. However, when I try to connect to the network...
We are trying to configure our device, which is custom based on nrf7002dk for interface certificate testing. The requirements for testing are
Ensure correct Internet Header...
Hello,
Im trying to flash my dev board but im keep getting following error:
Error: One or more batch tasks failed: * 1057707318: [Probe] Emulator error: Failed executing...
Currently, in the early stage of code development with NCS 2.8.0, I'm getting some errors when configuring I2C (TWIM) for a sensor device in a custom board.
The overlay...
On the NRF7001 module there is a "Determine the trim value" section in the documentation. I have followed the "Receive-based approach" to determine the CALIB_XO value. This...
Hi,
I have several deployed devices that have been running for a while, using the nRF Cloud A-GNSS system with the nRF Location library. These devices were successfully...
