Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
It is pretty straight-forward to use J-Link RTT Viewer on Windows (as described in the Debugging with Real Time Terminal tutorial ). Is there a similar viewer to use with...
Hi,
I am designing a bio-signal measurement circuit using nrf52832.
I wonder if there is any problem with the performance of nrf52 when using the sensor below.
Sensor1...
I can't comment in https://devzone.nordicsemi.com/f/nordic-q-a/56685/missing-ble_gatts_evt_hvn_tx_complete-events as it is closed but I am also seeing issues with the TX_COMPLETE...
Could you display on the ticket list page also when the ticket was last updated?
Now it shows only creation date, but I do not see indication which one was recently updated...
how can enable the security machanisim for nordic nrf52840
i want to use legacy connection with pass key entry feature
can anyone help me how to start ?
i am using ble_hrs_app...
Hello everyone, I have a network that consists of NRF52840 DK and multiple dongles that are pushing the collected data to central, I would like to retrieve data from this...
https://www.nordicsemi.com/-/media/Software-and-other-downloads/Desktop-software/nRF-command-line-tools/sw/Versions-10-x-x/nRF-Command-Line-Tools_10_6_0_OSX.tar
The file...
Hi,
we have developed a device with the nRF52832 that conncects with an Android smartphone. Our connection is secured and encrypted.
However, that doesn't really prevent...
Hi ,Nordic:
I used thingy:91 boards and firmware verison is thingy91_fw_2019-11-29_d3130d77, The board can connect to the nrf cloud, but cannot obtain gps data. We refer...
Hi
I'm reading the documentation and I have some doubts about the nRF9160 board.
So, the board is divided into the micro controller nRF9160 SiP ( https://infocenter.nordicsemi...
Hi Devzone:
I have 1 differential pair and 1 single ended pin I want to read, so I wrote code below into saadc_init function:
In this case AIN4 is the single ended pin...
Hello Support
When calling the function nrf_nvmc_page_erase(0xF7000) (In nrf_nvmc.c) I immediately get a Hardfault error when the code reaches the line where it calls wait_for_flash_ready...
Hi there,
I'm working on nrf52832 and using a PPI channel between a Timer and an SPI to output a voltage, for now, it works fine. But when I try to make it faster, e.g...
