Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi I have updated th nRF Connect for VS Code Extension Pack to the newest version. But when I want to enter Debug in VSCODE, the error comes out. Before upgrade, the debug...
Hello,
I am currently working with an nRF5340 configured to operate in High Voltage mode , where the main input supply is 5 V .
Issue description
When the nRF5340 is...
I just wanted to notify that I need to set CONFIG_SOC_NRF_FORCE_CONSTLAT=y in order for a NRF54L15 to be able to respond as a SPI slave (SPIS) using nrfx SPIS code.
Otherwise...
Hi,
I have developed custom hardware based on the nRF9151 chipset.
I would like to program the firmware using nRF Desktop (Programmer) with a third-party SEGGER J-Link...
Hi,
I am having trouble communicating between the nRF54L15 and the nRF7002 in a custom board. I flashed the scan sample. I made a new overlay as below:
/*
* Copyright...
Since about a week or two ago, I cannot flash (or debug/reset etc.) my device from the VSCode nrfConnect extension, when more than one device is connected to my PC. I am using...
Hi,
I am trying to confirm whether nRF54L15 as a chip officially supports the UTP OTA feature.
From the SoftDevice Controller documentation I can see that the following...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
I make a ble hid usb dongle with ncs2.0, ble keyboard send keycode to hid dongle, hid dongle send the keycode to computer.
When keyboard send keycode slow, it's work fine...
Using 54L15 DK for testing. Zephyr toolchain & SDK both v3.02. I have been through the DevAcadamy exercise which uses Blinky for its example, now I want to integrate into...
Hello,
I need help regarding flash memory read on nRF52840 device, SDk16, SD=340.
I have using the fds libarary for memory read/write in my code for many years now. However...
Hi,
I'm trying to scan for coded phy devices with the nrf-sniffer application.
Followed the guide and installed nrf-sniffer with the nrf-util.
In Wireshark it works...
We are using firmware 1.3.6 on the nRF9160. During testing, I ran into the reset loop restriction. To quickly get out of it, I issued a AT%XFACTORYRESET=0 command. (We are...
