Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello Nordic team,
We are making our own custom project, and we are facing problems in implementing lower power modes.
Reading from the info center, when the DK Board...
When initializing two channels, enter scan mode。After the two channels are converted, the callback function will be entered，Read conversion results。However, the requirements...
Hello
I am following a beginners tutorial on youtube and trying to implement simplest possible example of reading an analog value.
I want to use the nrfx library to do...
Hello,
I am working on a project where I am using 8 ADC channels on the nRF52832. When I run the code the device seems to get ADC values that look correct. But, if I pause...
I have an out-of-tree driver. It has an I2C that is working but also GPIO that are only working with compatible = "gpio-leds" but not with the driver compatible = "st,vl53lx...
On the nRF52840 there were many pins specified as "low frequency I/O only." Does the nRF53 have this same restriction? I don't see mention of these pins in the nRF53 datasheet...
Hello, I am working on application with nRF52833. What is max load current of internal LDO between VDDH - VDD? VDDH is 5V (USB) and VDD is 3.3V. There isn't anything about...
Hi
I am not busy developing an new product with nRF52840.
I want to use the BLE functionality and started with the ble_app_hrs sample application.
I download the pca10056...
Hi everybody,
I am trying install and set up Wireshark, i am in this step:
this is my output:
I think trhe problem is because of pyserial isn't detected, i have...
Hi,
I purchased a BLE dongle with your 3rd party HolyIoT: mini Holyiot-nRF52840-USB-Dongle. It is recognised on Nordic Connect, but not Nordic Programmer (Err msg: DFU trigger...
Dear devzone-team,
could you please tell me where the yaml files (like thingy91_nrf9160_ns.yaml) in the board folders are used?
I could not find a tool which evaluates...
I cannot get my solution to send data through the serial port.
I use the serial application to work on the instance 1.
static void sleep_handler(void) { __WFE(); __SEV...
Hi,
I am testing the nRF9160 DK and used the asset tracker application with the IBasis SIM. Application works fine under CAT M1 network (IBasis SIM is roaming on o2/Telefonica...
Hello
We want modify mcuboot_primary and mcuboot_secondary partition.
mcuboot_primary end_address change to 0x70000 and size change to 0x60000.
mcuboot_secondary end_address...
