Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
One of my nrf52840 DK cards wont detect as jlink, nor bootloader drive anymore. But I can still program it using a Segger jtag programmer and P18 port. Running Windows...
Hi.
My NCS version is 1.6.0. When trying to compile ./zephyr/samples/subsys/nvs for nrf9160_dk, I'm getting the following error:
Do I need to provide some custom overlay...
Hello, I recently bought the Laird BL654 DK which is based on the nRF52840. ( www.lairdconnect.com/bl654-ble-modules-and-development-kits) . I was interested in running the...
Hi. We are using the nRF52 sdk v15.2 with S132 v6.1.0 on a nRF52832. Sometimes, when connecting, we get a crash with
identifier 0x1
program counter 0x3FDA
fault information...
Hello,
I'm going to send data from a distance of 100-150m using Bluetooth long range communication.
When I looked up some examples of this, I saw that two development...
Hello!
Running Windows 10, nRF Connect for Desktop v3.7.0, Bluetooth Low Energy v2.5.2.
Have the following section added to the uuid_definitions.json:
The problem...
I am sending data over air from an XBee in transparent mode to an nRF52840 dongle as ZC.
The data is going over the air from the source and destination addresses using a...
Current status. Bond is required to perform FW updates while in OTA mode.
What we want: No Bond is required for FW update in OTA mode, FW files can be uploaded unilaterally...
Hi,
I have questions about the connections between the nRF5340 and the FEM nRF21540.
The nRF5340 has these components:
And the nRF21540 has this component:
I wonder...
Hi everyone,
I am currently reading the nRF53 Series product specification from the info center for evaluation purposes. During reading and looking at the application...
Hello.
Please forgive me for a real beginners question but I would like to understand the relation between the menu configurations in SES and the different configuration...
During a FW update, it failed for some reason and then I couldn't get anything to work. I can't come back from OTA mode. Reset does not work either.
According to the log...
I just found out there is no SPI slave support for SPI3 on NRF52840, but the memory map shows a SPI master for SPI3 though. Is it possible to enable SPI slave on SPI3? We...
