Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
Is it okay to supply the nRF21540 with a DC/DC or do I need to use an LDO? Are there any performance differences of the nRF21540 when choosing one over the other...
I'm finding that the signal strength of the radio is too low in my nRF52840 custom BLE project. I would like to increase the radio power from the default 0dB as our RSSI values...
I made a custom model under ncs1.6.0 to publish uart data. When the data I want to publish exceeds 85 bytes, an error occurs in debug:
<err> bt_conn: Unable to allocate...
NCS v1.6.0
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
When Serial LTE modem is woken up after #XSLEEP=2 without 2s delay, it starts to loose some unsolicited...
Hello,
I'm using the sdk v17.0.2 with softdevice s140 with a custom PCB shipping the nrf52840.
I'm facing an issue where I cannot enable NFC and softdevice at the same...
Hello everybody. I am currently evaluating some BLE Tags, if they can be used as an BLE doorkey. The chips I am talking about are the following: nRF51802 nRF51822 nRF52832...
Hello support team,
I try to get the NRF52840 DK to work as a central with FreeRTOS. Connecting and getting notifications works well, but the device freezes on a disconnect...
I am running a Zephyr OS, and I am using the mbedtls APIs to do my cryptographic operations using the Cryptocell as my backend. My question is should I be using a mutex of...
Hello,
We have a physiological monitoring system in production where we used NRF52832 as a peripheral. Connecting this peripheral with Windows bluetooth, we realised that...
Hello,
I'm currently looking at using a last will message that updates an attribute on the cloud if the device disconnects from the broker. The broker and client agrees...
Hello everyone,
My current setup:
1.Development Kits = NRF52840
2.Nrfutil Version = 6.0.1
3.Softdevice = S140
4. Operating System = Linux
In current goal is to...
Hi There,
I am currently using a custom bootloader for my devices which was started from the secure bootloader example given in the SDK, I am using BLE as the transport...
i have nRF Connect SDK v1.6.1，excuted “west update” and “west zephyr-export” command（the project will not built successfully without executing these 2 commands）
then i was...
ncs version 1.6
SES
Windows 10
I have installed ncs completely using standard tools.
Now I am following the tutorial Part 1.
The project hello_world is created...
