Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everybody,
I am running into the same issue as described in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50386/ble-scan-timeout-always-in-multiple-of-second...
I've been working with the NRF52840 for a while now. My setup is based on the CLI coordinator code and a bunch of end devices running the multisensor freertos based program...
I am trying to use a remaining timer/counter in the nrf52832 as a divide by 64 counter to get rid of an off board MC74HC4060 counter chip we are using for I2S from an external...
Hi Nordic Semiconductor!
Over the years I've been using your development kits, some days ago I got the nRF5340-DK and started on a new computer. Normally I dive into the...
I don't know why, but after issuing the nrfutil dfu command line, it takes ~34 seconds before the DFU starts and the progress bar is shown.
Sample command lines:
nrfutil...
Hello,
I want to use a FIFO. I want to send the data from file1.c and receive it on file2.c.
Currently, I have defiend my_fifo using K_FIFO_DEFINE(my_fifo) and using...
I am currently working on AoA direction finding solutons, and I have successfully run the demo direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hello,
I would like to ask you if there is an antenna layout available for the nRF52833. Indeed, I would like to develop my own application with it and, this SoC needs to...
Hello all,
I am currently working on receiving SAADC data and transmitting it through BLE with a sampling frequency of 1kHZ or higher. I am using nRF52832 board with the...
Hello, I have custom BLE service and characteristic as below image.
I wanted to discover them in ble central mode. I have modified ble_hrc_c.c to validate but central...
dear all
When I use QSPI to operate external flash and mount a FatFs file system, when I use RC = FS_ open(&file, fname, FS_ O_ CREATE | FS_ O_ WRITE); When creating a file...
Hello DevZone,
For my project I have a number of pins generating interrupts from different sensors.
I've read that GPIOTE IN events consume a bit more current than the...
nrf_mesh_config_app.h at the generic level mesh example contains constants like DEVICE_COMPANY_ID, DEVICE_PRODUCT_ID and DEVICE_VERSION_ID . I've expected those values to...
